Turbo-action 27255E/ES Turbo Hydro 200 Electronic Shift Valve B Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Turbo-action 27255E/ES Turbo Hydro 200 Electronic Shift Valve B herunter. Turbo Action 27255E/ES Turbo Hydro 200 Electronic Shift Valve Body (PRND21) User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 8
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
Part # 27255ES 1 3/02,5/04,3/07,12/07,6/09
1535 Owens Road, Jacksonville, FL 32218
Phone 904-741-4850 * Fax 904-741-4853
CHEETAH E-SHIFT Competition Electronic Valve Body - (PRN321)
Part #27255ES
Turbo Hydro 200 - 1979-86 Lockup
(Metric Marked on Pan Fig. #1)
FIRST, READ INSTRUCTIONS CAREFULLY, THEN PROCEED TO INSTALL VALVE BODY BY FOLLOWING
EACH STEP INDIVIDUALLY.
Note: #70600 CHEETAH E-SHIFT Controller Required. TH200 Lockup Pan & Filter Required.
CAUTION: Working on this transmission will require the use of metric tools.
The following tools and items will be required:
1 - Screwdriver
1 - Rachet and 3” Extension
1 - 13mm Socket (sometimes 1/2” will work)
1 - 10mm Socket
#14-#16 Gauge Wire (Length of wire will vary depending on your specific
application).
Suggest Amsoil or Dexron Transmission Fluid (Number of Qts. will vary
depending on the size of your torque converter & depth of pan).
Kit Includes: 1 - 27255ES Valve Body
1 - 27088-2 Special Valve Body Plate
1 - 27099C Pan Gasket
1 - 27097 Spacer Plate to Valve Body Gasket (Marked V.B.)
1 - 27098 Spacer Plate to Case Gasket (Marked C)
1 - 27103 Filter Gasket
1 - 23138 Set Screw (3/8”-16 x 5/16”)
1 - 24126 Set Screw (5/16”-18 x 1/4”)
1 - 27170-1 Aluminum Manifold
2 - 17381 Super Solenoids
2 - 17381R Retainers for Solenoids
2 - 27171-1 3/16” Manifold Tubes
1 - 24390-1 Solenoid Connector
1 - 24158 O-ring
2 - 27133 Metric Bolts
2 - 5011 1/4” Washers
2 - 00781A Female Snapplugs
2 - 50103 Contingency Decals
This Valve Body can be installed while in the car, however, for maximum durability and performance we
suggest taking the transmission apart. See Optional Steps section. Steps #12 thru #15.
STEP #1: Transmission should be cool before installing the Valve Body. Also, place gear shift selector in
park. If vehicle is on the ground, secure so it will not roll.
Seitenansicht 0
1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - Part #27255ES

Part # 27255ES 1 3/02,5/04,3/07,12/07,6/091535 Owens Road, Jacksonville, FL 32218Phone 904-741-4850 * Fax 904-741-4853CHEETAH E-SHIFT Competition Ele

Seite 2

Part # 27255ES 2 3/02,5/04,3/07,12/07,6/09STEP #2: Drain transmission by dropping pan at one end. Recommend leaving a couple of bolts at-tached unti

Seite 3

Part # 27255ES 3 3/02,5/04,3/07,12/07,6/09STEP #18: Now place bolt and manual detent roller and spring into place, being sure that manual valvewas lin

Seite 4

Part # 27255ES 4 3/02,5/04,3/07,12/07,6/09Fig. #1Pan Marked MetricFig. #2Filter Bolts & FilterFig. #3Throttle LeverBracket Assembly

Seite 5

Part # 27255ES 5 3/02,5/04,3/07,12/07,6/09Fig. #5Manual ValveFig. #4Manual Detent Roller & SpringFig. #6Valve Body with SpringFig. #7Valve Body Ga

Seite 6 - Ball Locations for Valve Body

Part # 27255ES 6 3/02,5/04,3/07,12/07,6/09#2 Remove#4 Remove#3Remove SpringThat Sets Here.Fig. #8Ball Locations for Valve Body##1 Remove

Seite 7 - Fig. #10

Part # 27255ES 7 3/02,5/04,3/07,12/07,6/09Fig. #10The two New LongerBolts go here.Manifold Tubesare epoxied here.Fig. #9Manifold Tubegoes here1-2Shift

Seite 8

Part # 27255ES 8 3/02,5/04,3/07,12/07,6/09Fig. #12Tap hole to governor 5/16-18 approximately 1/2”deep.Fig. #11ASolenoid ConnectorFig. #11BSolenoid Con

Kommentare zu diesen Handbüchern

Keine Kommentare